E510 PCI DRIVER

Always install DDR2 memory modules in the order indicated on the system board. To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. To connect a network cable, first plug the cable into the network port or device, and then plug the cable into the computer. See the documentation that came with the drive for instructions on installing any software required for drive operation. When removing an IDE drive data cable, grasp the colored pull-tab and pull until the connector detaches. To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module. Note the routing of the DC power cables underneath the routing clips in the computer frame as you remove them from the system board and drives.

Uploader: Mikasar
Date Added: 7 May 2005
File Size: 68.95 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 25280
Price: Free* [*Free Regsitration Required]

Memory purchased from Dell is covered under your computer warranty.

Dell Dimension – Wikipedia

To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer. The pin-1 end of a connector on a board or a card is cpi indicated by a silk-screened “1” printed directly on the board or card. To connect a network cable, first plug the cable into the network port or device, and then plug the cable into the computer.

Snap the bracket onto the new drive. S510 must route these cables properly when you replace them to prevent them from being pinched or crimped. See the documentation for the card for information about the card’s cable connections.

  LG MONITOR L177WSB DRIVER DOWNLOAD

If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. If you are installing or replacing a PCI Express card, follow the procedures in the next section. You must route the DC power cables properly through the routing clips when you replace the cables to prevent them from being pinched or crimped.

Use care when handling the front-panel release ppci to avoid damaging them. If the new floppy drive does not include shoulder screws, use lci screws within the drive panel insert. If you are installing or replacing a card, follow the procedures in the next section.

Removing and Installing Parts: Dell Dimension /E Service Manual

When installing the processor, do not touch any of the pins inside the socket or allow any objects to fall onto the pins in the socket. If you are installing a processor upgrade kit from Dell, discard the original heat-sink assembly. Most interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one r510 matches a tab or a filled-in hole on the other connector.

pfi To prevent static damage to components inside your computer, discharge static electricity from your body before you touch e50 of your computer’s electronic components.

When you connect an IDE interface cable, do not place the colored stripe away from pin 1 of the connector. Reversing the cable prevents the drive from operating and could damage the controller, the drive, or both. If you are installing a PCI Express x16 card, the card may cover the floppy-drive connectors.

Otherwise, your computer may not start properly. To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover. Ground yourself by touching an unpainted metal surface on the back of the computer. You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer.

  ACCUSYNC 90 DRIVER DOWNLOAD

Dell Dimension

The brackets also keep dust and dirt out of your computer. If you e501 installing a new drive, you need to remove the drive-panel insert.

You can do so by touching an unpainted 5e10 surface on the computer chassis. After you e10 the heat-sink assembly, lay the assembly on its side. Some network adapters automatically start the computer when they are connected to a network. Ensure that you release the securing tab to unseat the card. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you install your new processor.

Leave the release lever extended in the release position so that the socket is ready for the new processor.

Always install DDR2 memory modules in the order indicated on the system board. If necessary, disconnect any cables connected to the card.